The radian collection is a step up from the standard with simple, classic options in wiring devices, home automation controls, and screwless wall plates that complement today’s homes and hospitality settings.
Radiant Screwless Polycarbonate Wall Plates
• Available in 26-style openings.
• Extra 3/8″ width and height than Standard size wall plates.
• Provide better sheet rock coverage with standard size appearance.
• Molded of .065″ thick polycarbonate.
• 2-piece plastic subplate made of polycarbonate.
• Available in 3 metallic finishes and 6 standard colors.
- MODERN, LOW PROFILE: In keeping with today’s design trends
- SIMPLIFIED INSTALLATION: One-piece sub-plate mounts over the device, allowing you to simply snap on the wall plate with ease and install in minutes
- SCRATCH, DENT & CRACK RESISTANT: Molded of rugged .065″ thick polycarbonate for durability
- EXTENDED COMPATIBILITY: Opening accommodates all Decorator, NEMA-style devices
- SEAMLESSLY COMPLETE YOUR PROJECT OR REMODEL: Matches other radiant devices and screwless wall plates by Legrand – Pass & Seymour


![Top 10 ⭐ 2 Pack - SnapPower GuideLight 2 For Outlets [New Version - LED Light Bar] - Night Light - Electrical Outlet Wall Plate With LED Night Lights - Automatic On/Off Sensor - (Duplex, White) 😍 2 Top 10 ⭐ 2 Pack - SnapPower GuideLight 2 For Outlets [New Version - LED Light Bar] - Night Light - Electrical Outlet Wall Plate With LED Night Lights - Automatic On/Off Sensor - (Duplex, White) 😍 -Lighting & Ceiling Fans Shop 31Cr0vHcjHL](https://www.walllampstore.com/wp-content/uploads/2022/12/31Cr0vHcjHL-100x100.webp)






































The Reaper –
Recommenfed, but they ate pricey compared to the basic wall plates for devora light switches and electrical recepticals (outlets). But they do get rid of the screws showing and add a cleaner look.Electrician”s tip: Just know that the top and bottom corner metal tabs (the ones that look like mouse ears) on any switch or receptical, are there so you can bend the up to push the switch or receptical off the wall surface as needed to make it sit level and flush. Simply use a small screw driver and fold the tabs downward to lift the switch or receptical higher from the surface of the wall and/or the electrical box. This helps if the wall is uneven plaster, drywall, or textured or even stucco on exterior walls. Also helps for electrical boxes that are recessed too far into the wall. Never just tighten down a switch or receptical to the maximum and against the electrical box, unless that is even and flush with your surrounding wall surface. I like to use a small allen wrench to bend these tabs, as it as a short and long side to allow better leverage or in tight spaces.Once level and flush you can tighten the screws on the inner part section of the wall plates untill they sit flush too. Then just click on the top cover, with the two slots holes down. Then just use a small flathead screw driver in those holes to remove it when needed. I usually just gently lift it from the bottom and they pop right off.I also bought the 2 and 3 gang (2x 3x switches or recipticals) to use where I had multiple gangs in my kitchen and bathroom.
CaliBurito –
Works, my walls arent flat so it looks a bit weird
missdee212 –
Purchased this along with the Legrand receptacles. It is very sturdy and it looks great.
Linda M. –
This wall plate was the only one we could not find in a store. Looks amazing!
Ashraf patel –
The media could not be loaded. Easy to install
PAUL PIANO –
Easy to use
:) –
Always recommend Legrand for all electrical outlet needs.
AskHoffa –
Really easy install with a screw driver only.They really make such a difference especially if you just repainted. It just looks very sleek and modern.