- Brand: FUMENTON
- Light Source Type: LED
- Material: Polyvinyl Chloride
- Controller Type: Remote Control
- Number of Light Sources: 2
- Voltage: 24 Volts
- Wattage: 72 watts
- Control Method: Remote
- Easy Installation: Simple, tool-free installation and avoid soldering, 5050 4Pin RGB LED Strip Connector Kit, plug and play
- Wide Application: The connection between the lamp strip and the strip, the connection between the strip and the controller, the connection between the strip and the splitter
- Package Content : 8x LED Strip Jumper, 10x Gapless Connectors,12x L Shape Connectors, 2x T Shape Connectors, 1x 2 way RGBW splitter cable,2X 4 Pin female connector with bare wire terminal,20x 4 Pin Male to Male Connector,20x LED Strip Clips
- Operting Condition: These LED tape connectors support 0-4A current and 0-24V voltage input, heat resistance level from 20-100 degree


![Best Pirce ๐ LED Flush Mount Ceiling Light Fixture,10 Inch,18W [160W Equiv] 1450lm,3000K/4000K/5000K Black Modern Light Fixture, Dimmable Ceiling Lamp For Hallway,Kitchen,Bedroom,bathroom,ETL Listed Black-18w ๐ฅฐ 2 Best Pirce ๐ LED Flush Mount Ceiling Light Fixture,10 Inch,18W [160W Equiv] 1450lm,3000K/4000K/5000K Black Modern Light Fixture, Dimmable Ceiling Lamp For Hallway,Kitchen,Bedroom,bathroom,ETL Listed Black-18w ๐ฅฐ -Lighting & Ceiling Fans Shop 31meX5MetdS](https://www.walllampstore.com/wp-content/uploads/2022/12/31meX5MetdS-100x100.webp)




















Dana Johnston –
We have several sets of strip leds we wanted to install in some cabinets and around a fake fireplace mantel. Lots of 90 degree turns and the need to jump from a base to a door that is opened on occasion (a couple times a year to arrange decos.) This kit saved the day and worked WAY beyond my expectations. I have never cut LED strips and used jumpers and angles before so I was hesitant. I worried for nothing. The kit is so easy to use, The hardest part I had was remembering to peel back the tape before sliding in the strip. My first couple connections did have some issues with not making a complete connection (red didnt work) I figured it out (the copper foil on the strip had gotten pretty mangled and almost worn off as I kept connecting and un-connecting the strip). Word of advise is to double check your length and placement then make the connections and be done with it. I did’t use the t connector but did use every thing else and it all worked perfect. The only thing to really be aware of is that the connects are all labeled R,G,B, and + . It is not necessary to to match these with the corresponding letters on the strip as longs as your consistent across the strip (i.e. the blue (B) can plug into the + side as long as the Blue (B) is plugged into the + side at the other end. Once I realized this (it was a duh moment) install went even faster and easier. If you don’t currently check out the Amazon Giveaway pages you really should as these come up often and even if you don’t win they usually offer a discount (I saved $5 off the price!) There is enough included in this kit to do several installs. The only real negative I found was getting the connector clamp bars open and closed was a bit of work and several of them I had to give a squeeze with some pliers to relatch them
John Fretta –
I love the different wires that this comes with, but the right angle and T connectors are really hard to get to work. Neither of the T connectors that came with my set pass through Red or Green, only Blue and power
sandra l. wall –
very difficult with out Directions
Antonio Cabral –
Excellent
Doug hartman –
Used this product for back light on bar shelves.
Manuel –
I only used the โTโ and โLโ adapters. The kit could use more โTโ adapters to allow for wider variety of configurations. A few flaws were the pins that make contact with the copper terminals on the LED light. As soon as the light was secured or clipped in and some movement was made the next series would not turn on or the red green lights would not turn. I had to add some solder to the LED copper terminals to make a tighter fit at the adapter pins. This kit could use different sized screws. Overall good product.
Michael J. Tawyea –
Place these under A Standing Desk. I prepped everything with alcohol but a few weeks later spots started to droop. A bit of clear packing tap resolved all that… ?
az –
snap-on components are not that great- have to manipulate (raise/lower) pins on each connector with tweezers to get strips to insert with a good connection- snapping mechanism requires about 1mm clearance to close on bottom, so you can’t mount the connector directly to a channel surface and then close/open with ease- opening these things is a massive pain, you have to take out part of your strips from your channel and apply a lot of force, it simply cannot be done in-place